Thermoguard SafeCeilings One Coat Ultra Matt White

Flame Retardant Intumescent protection in a single coat for painted or new primed ceilings.

Also Insulating finish for ceilings over Safewalls Insulating Basecoat for plasterboard needing increased fire resistance on gray boards where:

  • pink fire boards were needed
  • one board installed where two needed
  • highly flammable, cyanide gas emitting foam insulation installed above ceilings

 

 

  • Sale
  • Regular price £61.50
Shipping calculated at checkout.


Description

Flame Retardant Intumescent protection in a single coat for painted or new primed ceilings.

Also Insulating finish for ceilings over Safewalls Insulating Basecoat for plasterboard needing increased fire resistance on gray boards where:

  • pink fire boards were needed
  • one board installed where two needed
  • highly flammable, cyanide gas emitting foam insulation installed above ceilings

Colours: White and pastel shades or Thermoguard Select colours

Key Benefits

  • Decorative fire upgrade and finish in one coat. Protects bare and painted ceilings coated with a combination of acrylic and vinyl types of paint to achieve BS EN Class B and old Class O These results achieved at UKAS approved Fire Test Laboratory.
  • Can be used as part of a system to achieve 30 or 60 minute Fire Resistance requires specification and additional coats
  • Finished system provides a smooth aesthetically pleasing matt finishes for internal ceilings. (For walls see Thermoguard Safewall Systems)

How it works: Onecoat Ceiling Fire Paint expands in a fire to create a resilient insulating barrier.

Fire Test: FIRE TEST STANDARDS in UKAS and EOTA - accredited Fire Test laboratory BS EN Class B s1 d0 (old Class 0 compliant) over multiple layers and combinations of waterbased painted surfaces identified as low/medium risk.
Pack Sizes: Sold in 25 sqm, 50 sqm and 100 sqm pack sizes to aid correct application

Coverage: Follow on can guide to coverage to enable project Certification.
Drying Times: In normal conditions product will be touch dry in an hour and fully dry after 4 hours
Application Do not apply in temperatures under 8°C or above 30°C. Conditions Maximum relative Humidity below 75%. Surface should be at least 3°C above the dew point.

Typical Use: This product is suitable for ceilings only
VOC Content: Low VOC EU limit for this product (cat A/i) is 140 g/l. This product contains 16 g/lv
Composition: Catalytic and safe vapour-emission compounds. 

Preparation
Surfaces to be clean dry and firmly adhering.
Ensure good ventilation.
Do not apply while condensation could occur during drying.


Application
1 good coat applied at 10 sqm per litre over White and Off White colours
Brush or Roller: Apply using a woven short pile roller sleeve or synthetic brush. Must be clean and fully hard dry before application of additional coats.
Spray: Pressure Pot and Gun conventional with hand-portable compressor – thin 5% water OR Airless Graco 1500, 3500 or equivalent. 3/8” line, 30 mesh filter on machine, no filter in gun. 521, 523, 621 or 623 tip
Ensure coverage is applied as per can i.e., 20 sqm can covers 20 sqm.

Certificates: Once the works are complete, a project and area specific Certificate available after due diligence via www.thermoguard.co.uk stating any project specification number.

Cleaning: Return as much unused material to its original container as possible. Wash brushes,
rollers and guns with clean water immediately following use.

Health and Safety: Please refer to the relevant Safety Data Sheet for full details of this product
Apply all products according to BS 6150:2019- Buildings Painting Code of Practice
Do not store this product in cold temperatures below 5°C or above 30°C.
Store in a dry secure place away from children or animals.
Dispose of in accordance with local authority waste disposal measures.
Do not pour into drains or watercourses. Reduce- Reuse- Recycle.